新聞中心
新聞資訊
聯系我們
山東途暢路橋工程有限公司
聯系人：石總
電話：18264104888
地址：山東省濟南市槐蔭區經一路273號群盛華城
冷再生機水穩層施工要注意什么？
來源：http://www.toppersin.com/ 日期：2021-07-05 發布人：
1、施工放樣應在施工前做好施工放樣。恢復中線時，直線段每15~20m設一樁，曲線段每10~15m設一樁，并在兩邊路肩邊沿外設指示樁，在指示樁上用顯著符號標出邊沿的計劃高掛基準線。
1. Construction lofting should be done well before construction. When restoring the central line, one pile shall be set every 15 ~ 20m in the straight line section and every 10 ~ 15m in the curve section. Besides, indicator piles shall be set outside the shoulder edge on both sides, and the planned high hanging datum line of the edge shall be marked with prominent symbols on the indicator piles.
2、拌和與運送水泥安穩碎石底底層選用會合拌制，拌和站設在百丈互通轉盤內的空地上。拌和前應測定各種規格的含水量，根據含水量、天氣情況和運距的長度調整用水量，保證混合料的含水量均勻、適宜。夏日施工時可先對碎石進行灑水濕潤。含水量要比含水量大1.0%，使混合料運到鋪筑地段，攤鋪后在碾壓時的含水量不小于好值。灰劑量按照標準規則的檢測頻率和方法進行，灰劑量缺乏時要及時加灰，保證灰劑量按大于協作比0.5％控制并符合技術標準需要，及時取樣進行試件成型
2. Mixing and transporting cement, the bottom layer of Stable Crushed Stone is mixed together, and the mixing station is set in the open space of Baizhang interchange turntable. Before mixing, the water content of various specifications shall be measured, and the water consumption shall be adjusted according to the water content, weather conditions and the length of transportation distance to ensure that the water content of the mixture is uniform and appropriate. In summer, the gravel can be watered first. The water content should be 1.0% higher than the water content, so that the mixture is transported to the paving section, and the water content during rolling after paving is not less than the good value. The ash dosage is carried out according to the detection frequency and method of the standard rules. When the ash dosage is insufficient, the ash should be added in time to ensure that the ash dosage is controlled by more than 0.5% of the collaboration ratio and meets the needs of the technical standards. The sample should be taken in time for the specimen molding
3、側模板在施工水穩層前在硬路肩及沒有計劃路緣石的部位行側模板支立，防止水穩層澆筑施工時水穩層澆筑出計劃邊線。側模支立時要行立模放樣，模板加固后進行校模、驗?zāi)！９┱J模板符合計劃需要并經監理工程師認可，答應進行水穩層澆筑后方可進行水穩層澆筑施工
3. Before the construction of the water stabilized layer, the side formwork shall be erected on the hard shoulder and the part without planned curb to prevent the water stabilized layer from pouring out of the planned sideline. When the side formwork is erected, the formwork lofting shall be carried out first, and the formwork shall be calibrated and inspected after the formwork is reinforced. It is admitted that the formwork meets the needs of the plan and is approved by the supervision engineer, and the water stable layer pouring construction can be carried out only after the water stable layer pouring is allowed
4、攤鋪在水穩層正式開工之前，應在監理工程師贊同的地址鋪筑長度為100~200米的試驗路段。在鋪筑試驗路段的過程中，應設專人掛線量測，做好調查和記載，研討、解決發現的各種疑問。試驗路段應在監理工程師的監督下進行，假設試驗路段經監理工程師贊同查驗，可作為耐久工程的一有些。
4. Before the construction of water stabilized layer, the test section with a length of 100-200m shall be paved at the address approved by the supervision engineer. In the process of paving the test section, a special person should be assigned to hang up the line for measurement, make investigation and record, discuss and solve various problems found. The test section shall be carried out under the supervision of the supervision engineer. It is assumed that the test section can be used as a part of the durability project after being approved and inspected by the supervision engineer.
如試驗段任何有些不合格，則將該有些挖除，再進行試驗段的試驗抵達復合需要的標準中止現場攤鋪選用兩臺攤鋪機階梯式聯合攤鋪工作，攤鋪機前后相距5~10m，攤鋪速度5km/h。攤鋪過程中應根據拌和才干和運送才干判定攤鋪速度，防止攤鋪機停機待料的情況。設一個三人小組跟在壓路機后邊， 及時粗集料帶或蜂窩，并及時彌補細混合料，攤鋪平整，嚴峻部位挖除后用符合需要的混合料添補，挖除深度不小于
If any part of the test section is unqualified, the part shall be excavated, and then the test of the test section shall be carried out until reaching the required standard. The site paving shall be stopped, and two pavers shall be selected for stepped joint paving. The distance between the front and back of the paver shall be 5 ~ 10m, and the paving speed shall be 5km / h. In the paving process, the paving speed shall be determined according to the mixing ability and transportation ability to prevent the paver from stopping for material. Set up a three person team to follow behind the roller, eliminate the coarse aggregate belt or honeycomb in time, make up the fine mixture in time, pave it smoothly, and use the mixture that meets the needs after the severe parts are excavated, and the excavation depth shall not be less than
5、碾壓（1）、在攤鋪、修整后立即用壓路機跟在攤鋪機后在全寬范圍內進行碾壓。按靜碾－弱振－強震－靜碾的程序進行碾壓施工，碾壓施工過程中壓路機行進速度控制在1.5km/h～3km/h（2）、碾壓程序應按試驗路段供認的方法施工。碾壓時，應堆疊1/2輪寬，后輪有必要逾越兩段的接縫處。各有些碾壓到的次數大概相同，兩邊應多壓2~3遍。壓實厚度為15cm，壓路機碾壓不到的當?shù)赜萌斯ず粚崱?/div>
5. Rolling (1), immediately after paving and finishing, use the roller to follow the paver and roll within the full width. The rolling construction shall be carried out according to the procedure of Static Rolling weak vibration strong vibration static rolling. During the rolling construction, the traveling speed of road roller shall be controlled at 1.5km/h ~ 3km / h (2). The rolling procedure shall be constructed according to the method admitted by the test section. When rolling, 1 / 2 wheel width should be stacked, and the rear wheel is necessary to go over the joint of the two sections. The rolling times of each part are about the same, and the two sides should be rolled 2 ~ 3 times more. The compaction thickness is 15cm, and if the roller can't reach it, it shall be tamped manually.
以上就是今天介紹的關于冷再生機租賃http://www.toppersin.com的影響因素，如果大家對本文內容感興趣，歡迎來電合作。
The above is today's introduction about the cold recycling machine rental http://www.toppersin.com Price factors, if you are interested in the content of this article, welcome to cooperate.
下一篇：路面冷再生機租賃的組成和工作原理！ 上一篇：為什么工程團隊都會選擇冷再生機租賃？
閱讀/ Recommended reading
- 冷再生機租賃：冷在生技術助力道路經濟快速恢復交通 2025-12-09
- 冷再生機租賃：乳化瀝青與泡沫瀝青冷再生技術發展 2025-12-06
- 冷再生機租賃：探索綠色養護新路徑，泡沫瀝青冷再生工藝 2025-12-08
- 冷再生機租賃：為什么要就地冷再生？ 2025-12-05
冷再生機租賃：公路基層全深式就地冷再生施工技術研究
[2025-12-10]
通過對老路開展取芯和挖探調查并記錄取芯及挖探情況，取芯試件試驗檢測發現，道路整體結構強度不足，路面基層發生較大面積破壞，此路段災毀恢復重建采用結構性修復以提高路面結構強度，提...
